The days of peering down the muzzle to gauge the fitness of a gun bore are over. The Lyman Borecam Pro gives you an inside look at your firetube.
How the Borecam Pro Gives You The Inside Edge:
Scope tube is 24-inches long, enough to inspect most rifles.
The device is wireless, making it much more manageable.
Capable of recording video and saving still images.
Produces images at 720p in both cases.
Fits barrels .20-caliber and larger.
There’s a great scene in Major League when the team finds out their pitcher with the rocket launcher for an arm is almost blind. They fit him with a pair of glasses, and the coach comments, “Seeing’s the most important thing.” Looking at the hideous frames he’s wearing, one of the other players replies, “It’s not that important.”
The Lyman Borecam Pro comes with all the goodies: Borecam, charging cable, adapter for every electrical system known to man, cleaning gear and instructions.
We used to peer down bores and as long as we saw daylight from the other end and a shiny surface, we called it good. Little did we know. Now, perhaps, we can know too much. A rifle that otherwise shoots excellent groups might show up at the gunsmith with a request to re-barrel it, saying, “The bore is too rough.”
The important thing to remember is actual performance. If your rifle shoots good groups (however you define them) and doesn’t foul quickly, does it matter how smooth your bore’s surface is?
Not really.
But if you find that your accuracy is starting to suffer or that you once could shoot all day long with little or no accuracy loss, and now after 100 rounds, your groups open up. It’s time to investigate.
Borecam Pro Gives You A Peek
Lyman to the rescue with the Borecam Pro. Usually, a borescope means optics, lenses, mirrors and some sort of light source—all piped down a barrel. That can be tough when you’re trying to inspect an AR barrel. Lyman originally had the Borecam, which was a borescope with a digital camera built-in and wired to a monitor. It worked, but it wasn’t ideal. Keeping the wire from getting tangled, or just dragging the monitor screen around, was a hassle. The Borecam has a 20-inch reach, which was a bit limiting.
So, for the Borecam Pro, Lyman moved on up. First, they made the scope tube 24-inches long. You can now look at the throat of a barrel going down from the muzzle. That saves the work of weaseling the scope over a stock, into a receiver, and past all the internals just to get to the chamber.
You use your cellphone or tablet as a Wi-Fi receptor to see the image, photograph it or video it and save or send on.
And then, they made it wireless. You can port the image to your phone or tablet, and as a result you can easily send it on to wherever you decide. Also, without wires involved, you can mount the phone or tablet (iOS or Android) in a spot that’s easy to see, and not have to worry about the wires moving the screen all over the bench as you push, pull or rotate the scope. You can record video and save still images—all at 720p resolution. The Borecam Pro fits down barrels of 20 caliber or larger, so that leaves out the various 17s—but any .22 LR or larger bore is fair game.
The Borecam Pro has a USB charging port in the handle, so you can charge it up as your first step and have it ready once you get the firearm disassembled, the bore cleaned (or not, if you want to see the horror), and clamped in your work rack or bench vise. The charging indicator light goes on when you start charging and then turns off when it reaches full charge. The power switch also controls the power of the bore light, allowing you to adjust the light to the level you need.
I wish I had access to something like this back when I was gunsmithing, to show customers what was what. But then again, back in the 1980s, this level of technology would’ve been akin to magic. Now, it’s just a bit over $300.
Considering the cost of a new barrel—which you might avoid spending if you have a Borecam Pro—it sounds like a smart investment.
For more information on the Borecam Pro, please visit lymanproducts.com.
Sig Custom Works’ new Spectre pistols include Sig’s two most popular handgun models, and they’re ready to be carried right out of the box.
Spectre Series Features:
Laser Engraved LXG Grip Module
Distressed Spectre XSeries Slide
XSeries Trigger
Optics Ready
XRay3 Day/Night Iron Sights
Sig handguns have been seeing greater success than usual in the U.S. market for a few years now. Their P365 XL is generally considered to be the king of micro-compact double-stack 9mm carry guns. And the army’s adoption of the P320 as the M17 service pistol helped to boost their popularity as well. Now Sig Custom Works has released the Spectre line which features the P365 XL and the P320 XCompact, both designed to be ideal concealed carry pieces without any further modification required (besides perhaps the addition of an optic).
Both Spectre pistols feature an LXG grip module which has been laser engraved with aggressive texturing to provide for a solid grip. They also include XSeries triggers, XRay3 Day/Night sights and an XSeries slide. The slides both feature Spectre X-pattern engravings and lightning cuts.
P320 XCompact LXG laser engraved grip and skeletonized XSeries trigger.
The P320 XCompact Spectre’s XSeries straight trigger has been skeletonized, something not found on the P365 version. The P320 also has more direct optics mounting options than the P365 XL, ready to accept a Sig Romeo1PRO, a Deltapoint PRO, or an RMR. The P365 Spectre is only cut for the Sig ROMEOZero.
The Spectre XSeries slides on both guns have also been intentionally distressed at the factory to give each one some unique character. It certainly looks cool, but it’s also a bit like buying pre-torn jeans. If you are training with your defensive handgun as rigorously as you should be, the finish should distress naturally.
The larger of the two Spectre pistols, the P320 XCompact is still small enough to be easily carried. It is more comfortable to shoot and has a bigger magazine capacity than the P365 XL, but comes at the cost of being less concealable.
The Spectre P365 XL
The regular P365 XL has already been lauded for how ergonomic and comfortable of a shooter it is despite its small size. This can only be more true on the custom Spectre model due to the aggressively engraved grip texture and improved XSeries straight trigger.
The Sig Spectre pistols have been listed for sale from $1099 to $1199. This may be a large sum for a carry pistol, but it has come to be expected for a custom gun of this quality. They each also ship with two magazines (15-round for the P320 XCompact and 12-round for the P365 XL), a certificate of authenticity, and a Sig Custom Works challenge coin.
Bushnell recently released their upgraded line of H2O waterproof binoculars. Their new aluminum body makes them light-weight and tough enough to be taken anywhere.
New H20 Waterproof Binocular Models:
7×50 Porro (MSRP $99.99)
8×25 FRP (MSRP $39.99)
8×42 FRP (MSRP $89.99)
8×42 Porro (MSRP $79.99)
10×42 FRP (MSRP $99.99)
10×42 Porro (MSRP $89.99)
10×25 FRP (MSRP $44.99)
12×42 Porro (MSRP $99.99)
12×25 FRP (MSRP $49.99)
Binoculars may seem pretty simple on the surface, but like any other piece of gear once you start seriously using them you may begin to better understand the nuance involved in their design. There’s more to a good pair of binoculars than just high magnification power. Good binoculars must balance weight, durability, image quality and price, and Bushnell’s new upgraded H2O line seems to do a good job of finding a happy medium between all of those factors.
What’s New?
While Bushnell’s original line of H2O binoculars was also advertised as waterproof, no specific promises were made regarding how deep or for how long. The improvements found on this new generation of H2O binos are sure to please those who spend time around water, as they have now been officially rated for being submergible up to one meter for up to 30 minutes without any seepage. If for some reason they do leak, they also include Bushnell’s 20-year Ironclad warranty. Between the improved waterproofing and warranty, one should not be afraid of treating these binoculars the way good gear was meant to be treated—rough.
They are constructed from a new aluminum chassis that not only makes the whole package lighter, but more durable than the old generation. This is great news for those who enjoy slogging through the bush with their binos strapped around their neck, as it should take a lot longer before these start to weigh you down. Holding them to your face for a prolonged amount of time should be easier as well.
All nine models also feature a textured rubber housing to ensure a good grip even after getting wet. This is a very good idea for binoculars primarily intended for marine use. The rubber housing should also provide added protection against being dropped if the rubber texturing proves to be insufficient for your butterfingers.
The optical quality has also been improved, a nice feature whether you’re using them to track game or just enjoying nature.
Models and Variations
The nine different models come in a variety of magnification strengths, objective lens sizes, and prices, so there should be a version that suits your needs and budget. Both Porro Prism and Folding Roof Prism (FRP) designs are available.
Available now with MSRPs ranging from $39.99 to $99.99, this new generation of Bushnell H2O waterproof binoculars seems like a solid choice. Whether your hobby is tracking game through wetlands or just birdwatching at the beach, Bushnell likely has the right tool for the job.
For more information on Bushnell, please visit bushnell.com.
Given perpetrators tend to travel in packs, learning to engage multiple targets effectively and efficiently is a key self-defense skill.
Despite the fact we often train with a single target when we go to the range or run drills, most self-defense situations aren’t going to be mono y mono. If you hear footsteps approaching you in a dimly lighted parking garage, in all likelihood there’ll be two or more sets. In turn, if you value your life, you’d better get squared away effectively engaging multiple targets.
Jamey Caldwell, an instructor at 1-Minute Out and former special operator, breaks down the tactics to successfully get hits on multiple targets. It’s a challenging chore, even though Caldwell makes it appear simple. The hangup, more than anything, is transitioning smoothly between targets—not the easiest task with adrenaline pumping and only seconds to react. However, there are three points worth keeping in mind when drilling effective and efficient target transition:
Let your lower body lead the way
Keep your upper body relaxed
Keep your eyes on the target
Let’s break this down briefly.
When it comes to moving target to target, you’re legs and hips should do a majority of the work. Larger muscle groups, using these parts of the body requires less effort while providing more stability in the transitions. As for the upper body, getting tense makes for much jerkier movements. Keeping your arms and shoulders relaxed relieves the rigidity and creates a much smoother movement to the next target. Finally, getting your eyes on the target helps you move your gun in position. Certainly, you’ll still utilize your red dot or front sight, however, you’ll slow yourself down and struggle with getting on target focusing on them in transitions.
Overall, Caldwell gives very sound advice. Of course, you’ve got to do your part. Don’t just listen and nod in agreement at his instruction. Apply it to your training and push to make engaging multiple targets second nature.
Has Hornady cooked up the ultimate long-range AR cartridge in its new sexy-six, the 6mm ARC?
What Exactly Is The 6mm ARC:
It is essentially a commercial version of the 6mm PPC.
Though, it has a slightly larger case capacity of 34 grains of water.
Given it's designed for AR-15 platform, its maximum average pressure is 52,000.
Its forte is long-range and outperforms nearly all other popular AR-15 cartridges in this arena.
If you consider the evolution of the rifle, the goal has always been—and remains—to shoot with extreme precision, as far as possible, while experiencing the least recoil and influence from wind and gravity. Just look at the evolution of .30-caliber rifle cartridges; we went from the .30-30, to the .30-06, to the .300 Winchester Magnum and now to the .300 PRC. The desire to overcome the adverse effects of wind and gravity push the design of cartridges and bullets, and shooters relish every advancement no matter how minute. So, when someone argues that we don’t need a new rifle cartridge, what they’re essentially saying is that there’s nothing to be created that’ll be desirable or useful.
Though ringing steel at past 1,000 yards with an AR-15 might not appeal to you at all, you cannot deny the fantastic ballistic performance of the newest version of the 6mm PPC, known as the 6mm ARC.
Well, that’s clearly not true. The enhancement of external ballistics has been the driving force behind cartridge creation since Louis-Nicolas Flobert’s 6mm parlor guns of the mid-1800s. Everyone wants to shoot harder, faster and flatter, so desire and utility clearly exist. This is particularly true of devotees of the AR-15. Both amateur and professional ballisticians have been trying to develop cartridges for that platform for a long time. Some of these cartridges, like the 300 Blackout, found great appeal. Others, like the .30 Remington AR, proved to be misunderstood. The latest attempt at extending the reach of the AR-15 is from Hornady, and it’s called the 6mm ARC.
According to Hornady, they identified a need for an “unnamed” Department of Defense entity and a concept cartridge was discussed. The entity showed extreme interest, so Hornady began development. Ultimately, the result of that collaboration is what’s now known as the commercially available 6mm ARC (Advanced Rifle Cartridge), which was adopted by that undisclosed government body. For what it’s worth, I’ve been fed the “secret government agency” line so many times that it means nothing to me. And, truth be told, it should mean even less to you. I don’t care if Carlos Hathcock himself divined his dream cartridge from upon high down to some engineer in the basement of Hornady; a cartridge either fills a desire and provides utility—or it doesn’t.
But, Why The 6mm ARC?
What exactly is the 6mm ARC? It’s indeed a new SAAMI (Sporting Arms and Ammunition Manufacturer’s Institute) approved cartridge. That means there exists a set of parameters and design specifications for ammunition and firearms manufacturers to follow when building ammunition or guns for it. This is critical, because for a cartridge to have any chance for commercial success it must be SAAMI approved. Otherwise, manufacturers avoid it like a Covid-infected anti. However, the 6mm ARC isn’t really as new as it might seem.
Hornady currently offers three loads for the 6mm ARC. There’s a 105-grain boat-tail hollow-point Black load, a 108-grain ELD Match load and a 103-grain ELD-X load.
Along about 1975, Dr. Louis Palmisano and Ferris Pindell took the .220 Russian case, which was based on the 7.62x39mm Soviet cartridge and necked it up to 6mm (0.244 inch), and they also changed the shoulder angle to 30 degrees. The cartridge was explicitly created for benchrest shooting and, in fact, developed a winning reputation. Ironically, even though the 6mm PPC never gained SAAMI approval, it found great popularity in the benchrest competition circuit where most shooters made their own brass and loaded their own ammo. It should be noted, however, that there are several versions of the 6mm PPC. Though they’re minutely different, this is a result of a cartridge not having SAAMI approval.
While some believe the 6mm ARC is based on the 6.5 Grendel cartridge, it’s really nothing more than yet another variation of the 6mm PPC. No doubt, the 6.5 Grendel was some inspiration for the 6mm ARC project, and it could be argued the 6.5 Grendel is nothing more than a necked-up 6mm PPC. Of course, since bullet diameter is the primary distinguishing feature of any cartridge, this makes the 6mm ARC a closer relative to the 6mm PPC. Case capacity of the 6mm PPC is about 33 grains of water. Case capacity of the 6mm ARC is 34 grains. The most critical difference is that in bolt-action rifles, from which the 6mm PPC is typically fired, according to the Western Powders Handloading Guide, the 6mm PPC is loaded to pressures approaching 60,000 psi.
For the purposes of slowing extraction and extending bolt life, Hornady set the maximum average operating pressure (MAP) of the 6mm ARC at 52,000 psi. This is identical to the SAAMI MAP of the 6.5 Grendel, but 3,000 psi less than that of the .223 Remington and .224 Valkyrie. This makes perfect sense for Department of Defense applications, where extremely high round counts are expected. Soldiers and civilians want their guns to last as long as possible, and less pressure equals less wear and a longer life.
Of course, I’m sure some shooters couldn’t care less about where a cartridge came from or his ancestral background. Most are interested in the ballistic performance and advantages it might offer over other cartridges. After all, like has already been established, harder hitting, faster flying and more gravity-defying cartridges have forever been the focus of cartridge and ammunition development. It matters not so much where and why we now have the 6mm ARC, what does matter is what it can do.
Shooters have been begging for a cartridge that’ll deliver true long-range performance from the AR-15 for a long time. With the 6mm ARC, they now have one that delivers.
It gets tricky when you try to compare the external ballistic performance of various cartridges. This is partly because there are so many variables to consider. It’s even more complicated when the cartridges being compared are of a different caliber. So, let’s set the table for a proper comparison.
The 6mm ARC was designed for the AR-15 platform. Can it be fired in a bolt-action rifle? Sure. And, I’m sure we’ll soon see bolt-action rifles chambered for it. However, since the faster-shooting 6mm Creedmoor or .243 Winchester won’t work in an AR-15, it’d make no sense comparing the 6mm ARC to either. What’s offered here is a comparison of the 6mm ARC to other current SAAMI-approved cartridges that are AR-15 compatible.
There are a variety of ways to make this comparison. We could look at muzzle velocity and energy, and trajectories, and we could obtain this data from advertised ballistics or actual testing. Since the problem the 6mm ARC was created to solve was that of long-range performance, comparing muzzle velocities is mostly a waste of time. By the same token, comparing actual chronographed velocities is, too; it’s not unusual to see drastic velocity variations from one rifle to the next. So, we’ll compare advertised velocities in conjunction with data obtained from a ballistics program to look at a prediction of long-range performance.
If you’re a hunter, Hornady’s Precision Hunter ELD-X load (Top) for the 6mm ARC gives the AR-15 more reach than it’s ever had before. With a muzzle velocity of 2,750 fps and a ballistic coefficient of 0.536, the 6mm ARC ELD Match (Middle) load is an outstanding long-range cartridge/load combination for the AR-15. To extend long-range performance, initially ammunition manufacturers loaded heavy and high BC bullets for the .223 Remington. This improved down-range performance, but only marginally and they required faster twist barrels.
If we do that, we see that the best performing 6mm ARC load—the Hornady ELD Match load— will take 2.04 seconds to travel 1,200 yards. The best factory 6.5 Grendel load will take 2.26 seconds to travel the same distance, and the .224 Valkyrie gets there in 2.15 seconds. The best load for the .223 Remington—the original chambering for the AR-15—takes about 2.36 seconds to travel 1,200 yards. This is what you might call definitive proof that the 6mm ARC is the best AR-15 cartridge at defying gravity and wind. This is possible due to the muzzle velocity of the cartridge and the high ballistic coefficient (BC) of the bullets Hornady loads for it. The ELD Match bullet has a BC of 0.536 and the ELD-X bullet’s BC is 0.512.
Due to these high BC bullets used by Hornady, the 6mm ARC not only retains velocity, it also retains energy. At distance, it’ll hit harder than the other three cartridges. The bullets will also remain supersonic at greater distances. If you’re a lover of the AR-15 and have been wanting to extend your effective range, this is all good news. However, keep in mind these comparisons were based on advertised velocities, which begs the question of what you can expect out of a 6mm ARC in the real world.
Testing Theory
To find out, I acquired a 6mm ARC from Wilson Combat; it was their Super Sniper model with an 18-inch barrel. The Hornady ELD-X and ELD match loads were tested form this rifle and delivered average muzzle velocities of 2,711 and 2,661 fps, respectively. Hornady advertises these loads at 2,750 fps for the ELD Match load and 2,800 fps for the ELD-X load. Out of the Wilson Combat Super Sniper, both loads clocked in at 89 fps less than advertised. If Hornady’s advertised velocities were, as most advertised velocities are, based on a 24-inch barrel, this equates to a very reasonable 14.8 fps loss in velocity for each inch of barrel loss.
The .224 Valkyrie (second from left) and 6.5 Grendel (third from left) come close to matching the long-range performance of the 6mm ARC (right), but both fall short. All three cartridges out-class the .223 Remington (left) when the distance gets long.
For argument’s sake, let’s just assume that the actual chronographed velocities from an 18-inch barrel are all you can ever expect to get out of the 6mm ARC from any barrel length. If those velocities are plugged into the ballistics calculator and compared to the advertised—not actual—muzzle velocities for the .223 Remington, .224 Valkyrie and 6.5 Grendel, the 6mm ARC still outperforms all three cartridges at 1,200 yards. This means the 6mm ARC is indeed the flattest-shooting commercial cartridge option out of the AR-15. This places it well within the definition of need, making it both desirable and damned useful.
It should also be mentioned that the Wilson Combat Super Sniper rifle delivered, as you might very well expect, fine precision. For five, five-shot groups at 100 yards, the ELD Match load averaged 1.046 inches and the ELD-X load 0.693 inch. How does that stack up against other AR cartridges? Based on my records and all the AR-15 rifles and cartridges I’ve tested over the years, average 100-yard precision is slightly more than 1.5 inches. So, not only is the 6mm ARC flat shooting, it can also deliver precision.
What’s it good for and will it hang around very long? Distance is its forte and with its 2020 introduction and ability to flatten the trajectory curve, the 6mm ARC might ought to have been called the “Corona cartridge.” If you want to shoot at distance with your AR-15, this is the cartridge.
Long-range precision shooting is one of the fastest-growing segments of the shooting sports. Though typically dominated by bolt-action rifles, with the 6mm ARC, shooters can now contend out to 1,000 yards and beyond with an AR-15.
I also predict that it’ll indeed be with us for a while, and not just in the AR-15 platform. It’s essentially a commercial version of the 6mm PPC so look for bolt-rifles to spring up soon. Well, at least as soon as this current ammunition and firearms buying spree subsides. Until then, you can pick up an AR-15 or a new upper chambered for the 6mm ARC and have an AR that shoots flatter than you ever imagined possible.
Editor's Note: This article originally appeared in the December 2020 issue of Gun Digest the Magazine.
The new Lo-Drag upper receiver from Luth-AR has been stripped of anything not integral to the function of the rifle to make it as lightweight and snag-free as possible.
Luth Lo-Drag Upper Features:
No Shell Deflector
No Forward Assist
No Dust Cover
Thicker Receiver Walls
When Eugene Stoner first designed the AR, it too did not have a shell deflector or forward assist, so in a way Luth’s new Lo-Drag upper is returning to its roots. Only at the insistence of the military were the forward assist and shell deflector added later on. Original ARs did have dust covers, however, so Luth’s design is taking things even a step further.
Similar low-profile uppers have been made before, but most have either been discontinued or include at least one of the three features omitted from Luth’s design. This new Lo-Drag upper will be more affordable and available than other low-profile designs on the market.
Featureless AR uppers like this are popular on varmint-gun and bench shooting builds, but there are other applications as well. If I were to build something based on the Lo-Drag upper, it would be streamlined in other areas to make it as lightweight as possible (the low weight is my favorite aspect of the AR platform in general). If you’re looking to build the lightest AR you can, try using the AR-15 parts weight database. This crowd-sourced databased is an excellent resource for finding the lightest parts possible.
That being said, it would be helpful if Luth-AR had bothered to list the Lo-Drag upper’s weight since that’s one of its main selling points. It may be a bit heavier than expected due to its thicker receiver walls which were added for extra strength, and its 6061-T6 aluminum construction is marginally heavier than MilSpec 7075-T6 alloy.
With an MSRP of $99, the Lo-Drag upper is an interesting new offering from Luth-AR. Personally though, I hope they start churning out more A1 uppers soon, there’s been a serious shortage lately.
For more information on Luth-AR, please visit luth-ar.com.
Once a common and inexpensive shotgun choice in America, Saiga 12s have surged in value since they were banned from importation in 2014. Are they still worth it?
What Are Saiga Shotguns?
Made At Izhmash Factory (Now Kalashnikov Concern) In Russia
Semi-Auto AK-Style Action
Made In 12-Gauge, 20-Gauge, And .410 Bore
Several Different Models Imported
Currently Only Available Secondhand
The American firearms market in the early 2000s was very different from what it is today. While there are a plethora of magazine-fed shotgun options available now, the shotgun world back then was still mostly dominated by tube-fed traditional designs. So, when Russia began exporting reliable, semi-automatic, magazine-fed shotguns based on the AK’s long-stroke piston system, it definitely turned a few heads.
Now that almost seven years have passed since their importation was banned, are Saiga shotguns still worth looking at?
20-Gauge Saiga, hunting model.
History
Saiga shotguns began their life shortly after the fall of the Soviet Union in the 1990s. Designed originally as a sporting and hunting shotgun for the Russian commercial market, its popularity quickly surged as people realized its potential for tactical applications. Shortly after, Izhmash began modifying the design to optimize it for police and military use. These changes included moving the trigger assembly forward to allow for the installation of standard AK furniture, including a folding stock. They also began making larger magazines for them and shortening their barrels. These tricked-out variants were mostly employed by Russian SWAT-style police units, like those attached to the MVD (Ministry of Internal Affairs).
Police agencies from several countries outside of Russia have procured Saiga shotguns as well, even including some French counter-terrorism units.
Over the years there were a plethora of Saiga shotgun models imported into the U.S. The most significant distinction between all of them, however, is the location of the trigger assembly. On the original hunting variants, which is the most common variant stateside, the trigger is at the bottommost part of the receiver, compatible with the hunting-style rifle stock. The other models have the trigger in the normal AK location, allowing for the use of standard furniture. Some of the hunting models in the U.S. have been converted, however, so if you are inspecting a Saiga with a standard AK pistol grip check for weld marks where the original pin holes may have been covered up. If done professionally, this is not a problem and generally raises their value and desirability.
When Saiga 12s were first imported and still relatively unknown, they would sell for about $350. By 2009, the price had gone up by about $200 and people were discussing whether they were still a good buy or not. Now after almost seven years since the last one entered the country, they sell for closer to $1,000 for even a basic, unconverted model.
Right Choice For You?
Saiga shotguns in any chambering are great, reliable guns. Their design left a serious impact on the tactical shotgun world and inspired many copies. So, if you want a semi-auto, magazine-fed shotgun, are Saigas still worth considering? At their current price, unfortunately, probably not due to the abundance of similar designs on the market today. Buying a Saiga today is very much an investment. With no more Russian guns to likely ever be imported again, all Russian AK variants have begun demanding a premium for their collectability. If that’s what you’re interested in doing, no problem, but for those looking for a shooter in the current year, it's probably best to look at some similarly designed guns that were not made in Russia.
For more information on Saiga shotguns, please visit kalashnikovconcern.com. Note that the manufacturer's site lists their current Saiga model offerings, many of which were never imported to the U.S.
Imported by Beretta USA, these six new lines of Sako cartridges will offer extreme accuracy and deadly performance for competition shooters and hunters alike.
New Sako Cartridge Lines:
TRG Precision
Powerhead Blade
Gamehead Pro
Gamehead
Speedhead
Super Hammerhead
Sako, based in Finland, has been producing arms and ammunition since the early 20th century. Today they are best known for their precision rifles and cartridges that are appreciated throughout the world by hunters, competitive shooters and anyone else who cares about extreme accuracy.
This new generation of Sako cartridge families aim to provide shooters with ammunition that performs exactly to their needs, whatever they might be. That’s why each of these new lines were tailored towards a specific goal and are available in a variety of calibers.
The New Sako Cartridge Lines
TRG Precision
Manufactured with consistent accuracy in mind, exclusively intended for competition use and long-range shooting. These cartridges are loaded with open-tipped, boat tail match bullets.
These new Sako cartridges are intended for hunting and are completely lead-free. They feature a copper blade tip and “5-Stage Terminal Architecture”, which intends to optimize the cartridge’s performance in any scenario. This design supposedly solves the most common issues with non-lead projectiles: under-expansion and over-fragmentation.
Available Calibers: 6.5 Creedmoor, .300 Win Mag, .30-06 SPRG, and .308 Win.
Gamehead Pro
This cartridge family was designed for taking medium-sized game at extreme distances. They are loaded with Sierra GameChanger projectiles which feature a polymer tip, precisely calculated jacket thickness, and a high ballistic coefficient. These factors result in a bullet that is able to resist high muzzle velocity to still have lethal expansion at longer ranges.
Available Calibers: .270 Win, 6.5 PRC, and 7mm Rem Mag.
Gamehead
For small to medium game, the Sako Gamehead cartridge line features a soft-point and a non-bonded core. Similar to the Gamehead Pro, this also results in rapid expansion only it is designed for smaller game at closer distances. Sako describes it as a great all-purpose hunting bullet.
Available Calibers: .243 Win.
Speedhead
These cartridges feature a full metal jacket projectile and are only available in .223 Remington, as they are designed for competition use, especially 3-gun. They are intended to deliver very consistent accuracy with low recoil impulse, making them ideal for when both the precision and the speed of your hits matter.
Available Calibers: .223 Rem.
Super Hammerhead
Like the name implies, these cartridges are heavy hitters. They feature a heavy jacket, non-fragmenting projectile, and a bonded core to provide good penetration and controlled expansion. These are intended for taking big game at relatively shorter ranges.
Available Calibers: 6.5 x 55 SE, 6.5 Creedmoor, .308 Win, .270 Win, and .30-06 SPRG.
For more information on Sako Cartridges, please visit sako.fi.
Considering current production rifles, slices its lineup in three ways: Hunting or Sporting, Target, and Biathlon. Sporting lineup variations through Anschütz North America include the Meister Grade Series with premium walnut stocks and the Canyon Creek Series with super-premium walnut. These rifles are largely magazine-fed repeaters. The Target rifles are geared toward Olympic-style positional shooting and benchrest and are primarily single shots. Anschütz has been slow to move into the NRL22-style precision market. Still, there are Custom Shop options — magazine-fed trainers available in laminated GRS stocks and a Rimfire Trainer Series in an XLR chassis. Think of Anschütz in broad categories of Sporting, Hunting, and Biathlon, but the real differentiator model to model is the action.
Anschütz has five primary rifle actions: the foundational Match 54; the variant 54.30; the practical and recently discontinued 64; the new swap-barrel 1761; and the straight-pull Fortner biathlon action. Anschütz has been deliberate over the years in its designs. Each action serves a purpose and serves it well.
54 Action
The Model 54 is effectively a three-lug design with a bank vault-strong lock up. There are two rear locking lugs on the solid steel bolt, plus the bolt handle’s lapped base that acts as the third lug. There is a short 53.5-degree bolt lift with a famously glass-slick raceway. The light firing pin travels less than 2 centimeters, which gives the 54 one of the fastest lock times in rimfire. The receiver is thicker and heavier than other actions in the Anschütz line and most rimfire actions in general, at least until the recent rise of centerfire-inspired Remington 700-footprint actions. This oversize makes a good support for heavy contour barrels. Most barrels are press fit with a dual retaining pin.
There are repeater and single-shot versions of the 54 action. The repeater magazines are a curved single-stack similar to a CZ mag. There are several trigger options, but the benchrest-quality two-stage 5018 is perhaps best regarded. It’s fully adjustable with a pull weight range of 2.1 to 8.6 ounces. I suspect the Model 54 with 5018 trigger is the winningest match receiver/action combo in smallbore history due to its long dominance across multiple disciplines. (The Winchester 52 may be close due to its long successful run. I have no data to support this either way.) But it is undoubtedly true that the 54 action and its excellent triggers put the Winchester and Remington 40x out of business at the elite shooting level almost overnight. The short bolt lift, lock up, lock time, and premium Anschütz rifle barrels came to define peak rimfire accuracy.
Current production 54 action rifles include the single-shot 1907, 1913, and 2013 match rifles. You can think of the 1907 barreled action as a lighter version of the 1913 with a slightly smaller barrel diameter. The 2013 action is an updated variant of the Match 54 single shot with an extended and squared bedding area and clamp-style barrel attachment. Anschütz uses the 54 action in the 1710 and 1712 sporter rifles. For silhouette and modern precision, shooting the 17xx line is the most widely used of the 54s.
54.30 Action
In 2015, Anschütz updated the single-shot 54 action with the 54.30. It moved the loading port rearward 30 millimeters, hence the 54.30, which reduced the overall action length by 18 percent. This change made the action stiffer and lessened the movement required by positional shooters to cycle it. The revision further lightened the firing pin for an even faster lock time. The 54.30 also has a threaded receiver and barrel connection, and it cut barrels with a new-to-2015 proprietary Anschütz match chamber. Not only that, the rounded footprint matches that of the 1907 and 1913. Depending on the stock, these positional rifles run between $4,700 and $5,500. That is a lot of money but represents almost a bargain compared to Bleiker, Feinwekbau, and other exalted European rifle makers, which can cost two or three times as much.
64 Action
The 64 action rifles are what most Americans think of when they think of an Anschütz rifle. For a long time, Savage imported them as Savage-Anschütz, and they’re all over the used market in .22 LR and .22 WMR. Newer version 64s — not imported by Savage — can be found on the used market in .17 HM2 and .17 HMR. The rifle that kicked off my obsession with rimfire was an Anschütz 1502 with the 64 action in .17 Mach 2. (You could blame this whole book on that rifle.) Anschütz discontinued the 64 in favor of the newer 1761 action. According to Steve Boelter, president of Anschütz North America, it received the last U.S. shipments of guns and service parts in December 2020. Shooters with 64s should not worry about future parts availability. “We have enough ejectors and firing pins to last a century,” he told me.
The 64 action is a scaled-down lightweight version of the 54, which suits sporter rifles and small game guns. The one-piece solid steel bolt body has no lugs. The locking surface is the base of the bolt handle. The 64 has a different trigger system, and while there are many good ones — Anschütz does not make a lousy trigger — there is no trigger model for the 64 that equals the two-stage 5018. The 64 and 54 are two different footprints, so stocks and triggers are not interchangeable between the two actions. The 64 barrels are press fit with one horizontal locking pin. The magazine release is less than ideal for position or bench shooting, but there are extended aftermarket options available to correct that. There was also a run in the 2000s where every new 64 seemed to have ejection issues. The case would eject slowly and often tumbled into the open receiver port. Engineers corrected this with a new ejector, and for a while, Anschütz sent them out for free or did the work themselves if you mailed them the bolt.
People ask, “What is more accurate, the 54 or the 64?” Mechanically, the 54 may have more accuracy potential with its heavy-duty build, locking lugs, and faster lock time. It certainly requires more hand finishing work and is a premium action. The barrels are made the same way, on the same machines, of the same or similar contours, with the same chambers. The 54 is a more sophisticated and expensive action, but to call it more accurate? Well, it depends. There are less-than-perfect 54s and barn-burner 64s, as is the nature of factory-built rifles. On average, the 54 series is more so a precision instrument. It has more potential as an accurate rifle system, but I’ve yet to shoot a 64 or know anyone who has one and complains about poor accuracy. The universal question on rimfire forums is always, “Is this rifle more accurate than that rifle?” The answer is almost always, “It depends.”
The newest Anschütz action, the 1761, has a host of modern features and has been designed to replace the 64 as a light, all-purpose, and relatively cost-effective platform. What started as a rework for the 1710 and 1712 Match 54 repeaters became a total redesign. As Anschütz put it in a good explainer on its North American website:
“…we opted to slightly increase the bolt lift from 53 to 60 degrees as a trade-off in order to move the locking lugs from the rear to the middle of the bolt. The lugs were switched from smaller eccentric lugs to a much more robust set of three lugs and evenly spaced these around the bolt. This allowed us to move from a long dual-spring firing pin to a very short, light firing pin and single-spring striker system. The new spring and striker mechanism was moved to the rear half of the bolt. This change also made the bolt much shorter in overall length.”
The bolt’s back is a roller bearing, making the opening motion smoother with less required force. The dual ejector system borrows from the single-shot Match 54. Ejectors are held in place by plunger and spring rather than c-clamp.
The smooth barrel tenon slip fits in the receiver like a CZ, but with one key difference: Rather than grub screws directly tensioning the tenon, there are two small v-blocks that Anschütz says more evenly distribute pressure and don’t mar the tenon. Shilen, Lilja, Lothar Walther, and other quality barrel makers produce drop-ins.
The steel billet receiver is CNC machined with an integral recoil lug and square bottom bedding surface. The action has square lines, not the rounded body of more traditional Anschütz rifle actions. It is 4 centimeters shorter than the Match 54 action (read: very rigid) and held down in the stock with two action screws. There is an 11mm dovetail rail on top. Anschütz opted not to tap it, which is a mistake. (The best Anschütz rings, according to many, including me, are the one-piece Talley rings and bases for the tapped receiver, not the more common 11mm dovetail clamp-style rings.)
The magazine is a steel and poly combo. As of early 2021, there were only 5-rounders, though a 10-round prototype has moved toward production. The small radiused hinge release button is behind the magazine and accessed through a cutout in the triggerguard. You can drop the mag with a forward slap of the trigger finger. The triggerguard is an unfortunate plastic, but steel models are available on the aftermarket. Calibers include .22 LR, .17 HMR and .22 WMR.
Fortner Action
Peter Fortner invented the straight-pull action that bears his name, and he still manufactures them in a small shop in Rohrdorf, Germany. Under a licensing agreement, his entire run of rimfire actions goes to Anschütz, which builds them into its flagship biathlon guns and the 1727 F line of sporting rifles in .22 LR, .17 HMR, and .17 Mach 2. Fortner also designed a centerfire equivalent for German rifle builder Heym. Boelter likens the Fortner relationship with Anschütz like a speed shop within an auto manufacturer, AMG within Mercedes.
Straight pulls operate faster than classic turn bolts, with less motion required to cycle them. Rather than the four movements of lifting the bolt, pulling it back, and pushing it forward, then pushing it back down again, there are just two motions to a straight pull: rearward and forward. Shooters typically run them with their thumb on the back of the bolt.
After the shot, the trigger finger comes up and cycles the bolt rearward. Then the thumb pushes it home on the fresh round. Much of Europe has outlawed semi-automatics, so when speed is needed, as in biathlon events or boar hunting dense forest with centerfires, straight pulls have proven fast and accurate. That explains why Anschütz, Heym, Blaser, and others have cultivated the design. Straight-pull actions have mostly gone unnoticed in the US of A. That’s because 1. we have all the guns, and 2. the cost. Straight pulls are necessarily complicated and expensive to make. The exceptions on this side of the pond are the Browning T-bolt and the Savage Impulse.
The Fortner action uses seven ball bearings that act like rear locking lugs. The action works very much like a hydraulic tractor hose or an air tool connection. When you put pressure on the bolt handle, it relieves stress on the bearings that sit within the sleeved bolt. This movement withdraws the ball bearings into the bolt, and you can cycle the action. The handle is spring-assisted, so the balls extend out and into the recesses in the receiver body and lock up when it snaps forward. This design allows for a linear rather than a rotating bolt action. Pulling the handle acts like pulling the collar on a quick-connect hydraulic line. It retracts the bearings and breaks the connection. Compared to a semi-automatic rimfire, this creates a stronger lockup. Advocates say they can run the bolt accurately almost as fast, too. Well, maybe. What is certain is the design is effortless to run. A broken-in Fortner seemingly wants to cycle itself with just some encouragement from forefinger and thumb. The Fortner action is rounded with a floating ring recoil lug and press-fit, two-pin barrel connection and comes with the world-class 5020 two-stage trigger with a pull weight range of 3.1 ounces to 1.375 pounds. Biathlon rifles come set at the required 500 grams or 1.1 pounds. The total package is a remarkable feat of firearm engineering.
SilencerCo’s new SCO15 lower receiver can bring several desirable, non-standard features to your next AR build without breaking the bank.
SCO15 Extra Features:
Ambi Bolt Catch
Flared Magwell
Integral QD Sling Cups
Integral Large Trigger Guard
SilencerCo, one of America’s premier silencer manufacturers, has recently decided to branch outside the realm of making guns quieter to try their hand at something a little more basic: AR-15 lowers.
With so many different AR lowers available, what makes the SCO15 special?
First, the not-so-special details. The SCO15 is built to mil-spec dimensions to be compatible with any common AR-15 components. It is constructed from 7075-T6 billet aluminum and finished with a type III hard coat anodization. This is all pretty standard, so now let’s get into what sets the SCO15 apart.
There is more reason to own an ambidextrous rifle than being left-handed. In the military, they teach soldiers how to fire their rifle with either hand in order to shoot from behind cover without exposing themselves to the enemy. Whatever your reasoning is for wanting an ambi lower, the SCO15 has you covered. Not only is the included, proprietary bolt catch fully ambidextrous, but the selector markings and QD sling cups are as well. With these features, the SCO15 can be assembled into a very versatile rifle that can be comfortably used from either shoulder.
It also includes an integral trigger guard which is larger than on standard lowers, providing more space for a gloved finger. This is presumably more durable as well since it is milled into the billet itself rather than being a separate piece.
The magwell is also flared to help expedite magazine changes.
There are other ambi lowers on the market, but they are typically either more expensive than the SCO15 or are similarly priced but have fewer features. At an MSRP of $249, the SCO15 is very competitively priced for what’s included in the package.
For more information on SilencerCo, please visit silencerco.com.
A gun safe is a hefty investment, but it pays off with peace of mind that your collection is secure against nearly any scenario.
What makes a quality gun safe:
Protects against both theft and fire.
Maintains internal temperature below 350° F in a 1,300° fire for around 1 hour.
10 gauge steel body and a thicker gauge door, preferably plate steel.
Box assembled with continuous welds.
Combination or electronic (keypad) lock.
Easily concealable in your home.
Attachable to the fabric of your home (i.e. floor or wall).
Holds existing collection with room for more guns in the future.
Interior lining to protect guns' finish.
Dehumidifier and lights top aftermarket upgrades.
Like breathing or blinking, meticulousness is naturally part of gun owners. Long range shooters record their every shot so they can predict where the next one will land. Handgunners spend countless hours perfecting every movement so pistol manipulation is glass-smooth and second nature. And clay shooters work overtime visualizing every possible way to track and vaporize blue rock mid-fight.
However, shooters, being human, are full of contradictions and the inborn quality to sweat the small stuff doesn't bleed over into every fiber of their passion. Perhaps, one of the most glaring examples is gun storage. We all know a few of them. The friend who has a tack-driver worth a couple grand he stows under his bed in the hard case it was sold in. It's playing with fire — potentially in a literal fashion.
Those who take their firearms seriously should also approach how they store them with the same gravity as they would dialing in a shot or scrubbing a bore to a mirror shine. Which is why, sooner rather than later, a gun safe should top the list of firearms necessities.
It's generally not an investment to take lightly since gun safes are expensive and the importance of the service they'll provide you and your collection. But, taking a studied approach, developing an understanding of exactly what they offer and weighing each one's benefits is certain to make your money well spent and give you priceless peace of mind.
Threats A Gun Safe Thwarts
Generally speaking, there are two primary threats to firearms in the home: fire and theft. For the most part, gun safe companies and the media pump up the former over the latter as the greater of the two and they're not off base. A house fire is, overall, a greater statistical danger. That said, these statistics are subjective; there are certain corners of the country where crime burns hotter than house fires. Ideally, just to be on the safe side, you should shop for a gun safe that protects against both.
Gun safe thwarts attempted break-in.
An additional point, while not a threat in a traditional sense, a gun safe also provides a way to control access to your guns, an important factor, especially if you have children. As Massad Ayoob points out in his book Gun Safety, realistically there is no way to gun-proof your home, so you must gun-proof your child by teaching them the respect and responsibility of owning firearms. Nevertheless, sometime in their life, they might have less-than-mature friends who formulate less-than-mature notions. Nipping catastrophe in the bud with Cannon, Winchester or what have you safe is well worth the investment.
Types Of Gun Safes
Not all gun safes are created equal. In fact, not all gun safes are really gun safe. For the most part, there are two types of gun storage options: actual gun safes and gun lockers. Confusingly, for the sake of marketing juice, many gun lockers call themselves gun safes. Clear as mud now? There's no bright line between safe and locker, but if there is a major distinction it's fire protection. Gun safes have it, lockers don't.
Depending on steel gauge, lockers are a viable option, especially for those who have certain constraints. If you rent a fourth-floor apartment, a light-weight, quality built system by Stack-On or SecureIt could be your only avenue to gun security. Few building owners are keen on testing the structural integrity of a floor by pressing down on it with 500-plus-pounds of metal box.
SecureIt Agile Gun Locker
For smaller collections, there's an oddball selection of handgun safes, rapid-access safes (a handgun safe for the most part) and hidden gun safes. In general, most of these systems hold no more than a few guns — typically one handgun — and offer no true security or fire protection. All in all, they secure a gun and offer fast access, usually next to a bed, in a closet or in a vehicle.
Secure More Gun Safe Knowledge:
The 5 Best Gun Safe Options For Protecting Your Collection
They're dynamite at what they're designed for, Hornady RAPiD Safes and Gun Box are excellent systems that deliver a handgun in a moment's notice. They and others are suitable to thwart crimes of opportunity or keep a gun under lock and key around children. But with time, most won't weather a serious attack with something a simple as a pry bar or claw hammer.
There are some exceptions. Fort Knox, for instance, manufactures a number of heavy-duty handgun and long-gun boxes hefty enough to withstand a serious break-in attempt. As always, expect to pay more when you go this route. True security never comes cheap.
Finally, there are good old-fashioned gun cabinets — which are not safes at all. Beautifully showcasing a collection, these elegant gun storage options (generally made of wood and glass) are long on looks and short on protection. Unless you have the money to slap a plate-steel door on a fire-protected room to create a walk-in gun vault, gun cabinets are generally not the top option.
Gun Safe Fire Protection
If you're a fan of cutting out ingrown toenails or filing your taxes, you'll love figuring out gun safe fire ratings. They are painful and frustrating in one felled swoop.
The fly in the ointment — testing. There is no set standard to determine how long and at what exterior temperature a gun safe will keep its contents from turning into a pile of scorched metal and charcoal (puddle of gunk for synthetic stocks). Each individual company contract independent laboratories to bake, burn and singe their safes, while keeping tabs on what happens inside. In turn, how Heritage has a gun safe put to the flame is different than Browning and Liberty. This isn't to imply the companies aren't on the up-and-up, at least a great majority. But at the bare minimum comparing fire ratings is an apples and oranges affair where “buyer beware” is the guiding light.
Photo: Prosteel
Great, then how can you actually find a fireproof gun safe worth its salt? It's tricky, but a good starting place is understanding what a safe is up against in a residential fire. God forbid, but if your house were to burn to the ground, it would take — on average — 60 minutes and would potentially generate temperatures as high as 1,300-degrees Fahrenheit. Thankfully, it generally doesn't reach this point, given typically first responders are on scene within 10 to 15 minutes after being alerted. In turn, most fires are quelled within the first hour.
The 350-degree Fahrenheit mark for internal temperature, the line where most companies certify their safes too, for an hour and beyond is a solid starting point. Additionally, a reputable retailer who specializes in gun safes is worth his weight in gold when it comes to finding which ratings actually live up to their billing.
It’s All In The Steel
Mercifully, safe security is much more cut and dried than fire protection. It comes down to cold, hard steel. That's pretty hard to fudge.
Conveniently for shooters, shopping gun safe steel is fairly simple, given thickness is expressed in gauges. And just like shotguns, smaller numbers mean more. From there it's a cakewalk, the thicker the steel, the more protection.
Before talking about how much and where the steel needs to go, we should look into how a thief will most likely attack a gun safe. He won't be a Hollywood cat burglar, deftly swooping the dial with a stethoscope in his ears. He'll be brutal, trying to pry the door open, cut a hole in the body with a non-torch method (read fire ax or grinder) or, in rare cases, using a torch. Keep in mind, the fire barrier in the walls does nothing for security — gypsum or concrete, it will crumble.
Liberty Gun Safe endures shotgun blasts.
In general, what's the best gauge of steel to start from? Many in the industry set 10-gauge (.1345 inch) as the minimum for the body of the safe. The door, in most cases, is thicker than the body, given this is a main area of attack. And don't get fooled by thickness measured with your naked eye. In many cases, those massive walls and door are that way due to the fire barrier sandwiched between them. Honestly, a thin door might offer better security than something that looks half-a-mile thick. One final point, how all that steel is stitched together to become a gun safe is important too. Full continuous welding, as opposed to bolts or spot welds, makes for a sturdier box — not only against thieves, but also fire.
Gun Safe Lock Options
Now you have your gun safe picked out and are confident about its security and fire protection, it's time to figure out how you'll access your treasures. For the most part, modern gun safes use three access methods: combination lock, electronic lock and biometric lock. As you've probably already guessed, they each have their own advantages and drawbacks.
Starting with the most traditional, the combination lock is the picture of simplicity and reliability. Merely spin the dial and unlock the door; the only weak link in the process is you and your faulty memory. However, if you're in and out of your safe a lot the process of left four, right two, left one gets arduous. Additionally, if you need a gun in a pinch, a combination lock is far from lightning fast.
Electronic locks, on the other hand, speed up the process considerably, just punch in a code. Furthermore, they offer a number of unique features that make a gun safe extremely user-friendly and increase their security. Many are programmable for multiple user combinations, they don't require a locksmith to change the code, they can incorporate with home security systems and lockout on multiple entries of the wrong code. The drawback of this system — electricity. If you don't have juice, you can't get to your guns. At a bare minimum this requires constantly staying on top of batteries, at the worst, it means no access to your guns when you need them most.
Electronic lock on a SecureIt gun locker.
Recently, with concerns of EMP attacks, some manufacturers — Fort Knox, Hollon Republic, Cannon, for example — have begun including a redundant combination lock. Meant as a backup, for those willing to shell out extra money it could provide a reassuring insurance policy for getting to your guns if your 9-volt battery supply runs thin.
Finally, there's the biometric gun safe. A riff off the electric variety, the lock scans a users fingerprint and gives them instant access to their guns. Additionally, it can store multiple users' fingerprints, so an entire family can gain access to a gun safe. Along with the drawbacks of the electronic locks, biometrics have another flaw — the technology isn't 100 percent. If your hands are dirty or you've been eating cheese puffs you might have difficulty getting into your safe.
Gun Safe Installation
Like “Fight Club,” the first line of defense for a gun safe is you don't talk about your gun safe. It might look pretty slick in your main room right next to the TV, but it's an open invitation, letting potential bad guys know you have something worth storing in a safe. A hidden gun safe is a safe gun safe. Secondly, if you move your gun safe around with a dolly or a buddy's help, so can a crook. Bolt the bugger down! Most every single one comes with floor attachments, use them.
Where Does The Dang Thing Go?
Face it, a gun safe is a big investment in the most literal sense. In all likelihood, unless you're into Elizabethan Armoires (we know you aren’t), chances are you’re vault is going to be among the largest and weightiest objects in your house. Safe to say, finding a place for your safe to reside isn’t the easiest exercise.
A general rule of thumb, especially if it's on the foundation, the ground floor is the best place to situate a gun safe. Structurally, it provides the support required to hold the mammoth without damaging your house and it provides a rock-solid surface to anchor it. Anchoring is always advisable, given thieves can’t just roll out the door with your safe to break into at their leisure. However, the second floor in a properly constructed house typically has the chops to hold a moderately sized safe. High-end options, pushing well north of 1,000 pounds might require consultation and modification by a skilled contractor.
Garages are often popular areas in a house to plant a gun safe, however, they can prove treacherous. If it’s your run-of-the-mill car hold, the area can be more permeable than the rest of the house giving greater access to felonious meatheads. Furthermore, few folks heat or air-condition their garage, in turn, it’s akin to storing your precious firearms outside. Not ideal.A dehumidifier is a must if you stow your gun safe with your cars. Plus, the garage isn’t the most accessible area in the house, kind of putting you in a pinch if you need to retrieve a gun right away.
But I Live In An Apartment…
Folks living in apartments and condos are in a sticky situation when it comes to gun safes. Many complexes won’t allow a large specimen in a unit for fear of structural damage. And almost all will refuse to allow a tenant or owner to attach it to the fabric of the building, which might put your collection at risk. Though, it never hurts to inquire with your landlord or homeowners association. If they say no to big units and bolting, what’s the solution?
Modular safes, such as the SnapeSafe Titan, are ideal if you live on the top floor of a condo complex.
On the end of the gun safe itself, it's fairly simple—either go a gun locker route or buy a smaller safe. These will generally conform to complex standards and won’t run you headlong in the powers that be. True enough, a locker doesn’t offer fire protection, but it’s a tradeoff you might have to make for security. There are elegant solutions in terms of safes proper, especially if you live on the 14th floor. Modular gun safes, for example. Options, such as the SnapSafe Titan, internally bolt together, meaning you can bring each piece up individually. Again, they don’t measure up to their seam-welded cousins, but they offer more peace of mind than nothing.
As far as keeping a gun safe or locker in one place if you can’t bolt it down, you’ll have to get creative. One of the more inventive ideas, bolting it to a steel plate larger than the door frame. Another is attaching multiple safes or lockers together. These small steps won’t guarantee a safe will stay on-premises, but you’ve made it a magnitude harder and more time-consuming for a thief to get it out of your place.
Size Of Gun Safe You Need
How big you should go is a tricky proposition. It's easy to save money and buy for your present needs. A more prudent course of action is planning for the future and purchasing a gun safe that will handle guns you'll add to your collection. Yes, it is more expensive now, but cheaper in the long run, given it saves you from another safe purchase.
Gun Safe Interiors
Some gun safes come with everything short of a minibar. But what you really need is up to you. The bare minimum is a soft lining, so you don't have to worry about dinging your firearms when you take them out. More recently, configurable interiors have become all the rage, giving you the ability to customize how you store everything. Another plus, for an electrically wired gun safe, is interior lighting. It's hard to believe how dark they can get. While all nice, don't get caught up in how many cup holders and digital clocks a gun safe has, what you're really concerned about is what’s under the hood — how it will protect your guns.
Gun Safe Accessories
Cannon Gun Safe silicon gel gun safe dehumidifier.
The No. 1 must-have extra for a gun safe — particularly if you live in a damp climate — is a gun safe dehumidifier. Gun safes can get moist quickly — not good for gun steel. There are primary two to choose from: electric and desiccant. The electric variety, such as Eva-Dry Mini Dehumidifier or Lockdown Dehumidifier Rod, are handy since they are non-toxic and spill free. But they have the same weak point of everything electric — electricity. Desiccants, on the other hand, take out the concern of not working when there's no juice. Something such as Dry-Packs Silica Gel Canister is rather benign, but must be emptied and dried at certain points for full effectiveness.
Parting Shot
It's easy to get chintzy and play the odds with your precious guns. After all, nothing has happened up to this point right? But when you take a sober look at the threats your firearms face when not in use then the need of a gun safe becomes evident.
It's a small investment when compared to the potential loss of thousands of dollars worth of guns, not to mention the priceless sentimental value. There's only one granddad's deer rifle in the world that you of all the grandchildren were bequeathed. You should act like you deserve by treating it like the treasure it is.
Don't fret! Rock Island's STK100 is the company's first striker-fired pistol, but it decidedly breaks from the herd.
How The STK100 Set Itself Apart From Other Striker-Fired Pistols:
Lightwight aluminum-alloy frame.
Similar ergonomics to the 1911, including beavertail and straight grip rake.
Lightening cuts in the slide to improve cycle rate.
Excellent 17+1 capacity.
If you know Rock Island Armory even in the slightest, you know the cut of their jib. For years now, the company chipped away a solid niche as one of the world’s foremost purveyors of affordable 1911 pistols. Good ones at that. Maybe not hand-tuned, custom-made good, but solid enough to trust your life as a personal defense piece. But the only constant in the world being change, the Filipino gunmaker recently made a big shift.
Say hello to Rock Island’s first striker-fired pistol—the STK100. Yes, the staunch defenders of John Moses Browning’s iconic pistol succumbed to the whims of the modern shooter and joined the current of today’s dominant handgun design. We’ll give you a second to scrape your jaw off the keyboard. Better? Good. While the move may chagrin purest who insist all their heaters boast hammers, there’s much to like about the way Rock Island has leaped into the modern fray. To be sure, the STK100 is a striker-fired 9mm, but a decidedly non-conformist take on this popular and omnipresent class of pistol.
Metal Head
Where Rock Island has taken a different tack is decoupling “striker-fired” from “polymer-framed”. Indeed, the gunmaker has opted for what it knows best to build the STK100, metal—in this case, an aluminum alloy. In some respects, the material ends up being a best-of-both-worlds option, offering what is generally considered a more robust frame material than polymer, but proving lighter than steel and corrosion-resistant. Plus, it appeals to folks who still turn a jaundiced eye at “plastic” guns.
Ergonomically, Rock Island has stayed close to home. The STK100 takes many cues from the good ol’ 1911, particularly in its relatively straight grip rake as well as fairly prominent beavertail. Evolution has all but done away with the latter on most polymer guns, which sport a little more than a nub. However, it and the grip angle make the pistol instantly familiar and comfortable, as well as facilitates a fundamentally sound high grip. The uncut trigger guard pulls its weight here too.
STK100 Tweaks
The gunmaker hasn’t remained a complete slave to tradition, adding some welcome tweaks. There’s a slight swell to the 9mm’s backstrap, helping it conform to the palm better. And the texturing is milled directly into the frame and grip proper—four panels of diamond checkering on the flats and horizontal and diagonal cuts on the front and back respectively. Additionally, the slide has cocking serrations fore and aft making the pistol easier to manipulate. Though, lightening cuts, three on each side, minimize the volume of serrations up front.
As for the tale of the tape, the STK100 is a 17+1 duty-sized pistol, sporting a 4.5-inch barrel and tipping the scales at 28.8 ounces. Given its moderate heft, the gun should make the double-stack 9mm a kitten, thus fast and accurate shot to shot—even a bit more so with the slide lightened up thanks to the cuts. Certainly, these dimensions are not out-of-bounds for a concealed carry gun, especially for those who don’t mind packing a bit more pistol. And Rock Island is surely angling the gun that way, outfitting it with an accessory rail.
The STK100 comes optic ready, with a slide cut compatible with popular red-dot optics (though Rock Island does not specify exactly which ones). However, the gun is ready for action out of the box wearing a set of the almost universal white three-dot sights. The trigger is one area where Rock Island joined the herd—yup the same blade safety outfit you find on nearly every striker-fired. As for its break, it’s in line with the crowd as well, tripping at between 3 and 7 pounds fresh from the factory. As to finish, the aluminum is anodized and the steel slide and barrel a matte-black Parkerization.
RIA has made a name for itself among penny pinchers after quality and the STK100 doesn’t disappoint with an MSRP of $599. Give other gunmakers are presently turning out metal-framed premium editions of their cornerstone striker-fired pistols, Rock Island little ditty might have the stuff to play spoiler among the top-shelf gang.
Rock Island STK100 Specs Caliber: 9mm Capacity: 17+1 Barrel Length: 4.5 inches Overall Length: 7.91 inches Overall Width: 1.25 inches Overall Height: 5.16 inches Weight: 28.8 ounces Front Sight: Tenon Cut W/ Retaining Screw Rear Sight: Fixed Integrated on Optic Cover Plate Grips: Aluminum (Integrated On Frame) Finish: Black Anodized Trigger-Pull Weight: 3-7 pounds MSRP: $599
For more information on the Rock Island Armory STK100, please visit armscor.com.
While the Benelli M4 was dominating the international combat shotgun market, others found a better, cheaper solution in the 12-gauge AK shotgun.
Advantages Of AK Shotguns:
Higher Potential Ammo Capacity
Magazine-Fed
Reliable Semi-Auto Function
Simple Operation And Controls
Modular Design
Russians are famous, or maybe infamous, for viewing the Kalashnikov as the solution to all their armament needs. Need a submachinegun? Vityaz—9mm AK. Need general-purpose machinegun? PKM—big, upside-down AK. Need a shotgun? You already know the answer.
Since their advent in the 1990’s, AK shotguns have grown in popularity amongst sport-shooters and law enforcement alike around the world. While other weapons in the Kalashnikov family have seldom seen use by Western armed forces, AK shotguns have been a notable exception. When even NATO forces are willing to be seen using Soviet-derived technology, you know it must be pretty damn good.
Vepr-12 AK shotgun.
Design And History
There isn’t much that can be said about AK shotguns’ design; they are truly just AKs chambered for shotgun shells. Things like the receiver and bolt group have been scaled up to accommodate the larger ammunition, and the gas block is typically adjustable, but besides that, there isn’t much difference between an AK shotgun and a traditional AK rifle.
The first AK shotgun designed and produced was the Saiga. Made in the famous IZHMASH factory in Russia, they entered production in 1997 and were available in 12-gauge, 20-gauge, and .410 bore. Early designs were intended more for sport and hunting, as evidenced by the fixed-stock and 5-round magazines.
It didn’t take long for these Saigas to be modified and adopted by Russian police and military units as well. They were given folding stocks, larger magazines, and rail segments for accessories.
AK shotguns are also popular home defense options in Russia because smoothbore weapons are easier to legally own than rifles or pistols.
After a few years of the Saiga gaining popularity, the Russian Molot factory decided to make their own AK shotgun in 2003. Their version is called the Vepr-12 and is based on the RPK that Molot is famous for producing. This means that Veprs have a thicker receiver and bulged front trunnion while Saigas do not, making Veprs the more robust and desirable of the two. Since then, there have also been American, Chinese and Turkish-made AK shotgun copies as well, though none are as good as the original Russian variants.
The use of AK shotguns by police and military units began in Russia and quickly spread to ex-Soviet satellite states that also traditionally used Russian gear like Belarus and Kazakhstan. While this is very typical, the adoption of AK shotguns in Western Europe and America is very unusual.
When nations select weapons for procurement, it is not a true meritocracy. Politics have sway over these decisions, and that typically means that NATO-aligned countries are opposed to using Soviet or Russian-designed weapons, and Russia typically prefers to use its domestic designs over Western guns. It is certainly a testament to the quality of Russian AK shotguns that they have been bought and used by French anti-terror units as well as the U.S. Coast Guard’s Deployable Specialized Forces. Some have also supposedly been sold to German and Italian police, as well.
Nobody denies the Benelli M4 is a world-class shotgun. Despite not being a member of the AK family, it is also an extremely reliable and durable machine. Its reliability is the key factor in its popularity with military and police users, but how does it compare to AK shotguns?
While there are a few different makes and models of AK shotgun, the nicest one is arguably the Molot Vepr-12 so we will use it for the sake of comparison.
Benelli M4s have several features designed specifically for combat. These include a larger-than-average ammunition capacity, a telescoping stock, and a large loading port. These are certainly advantages when compared to more traditional shotguns, but they are less impressive when compared to the Vepr-12.
While the M4 has a maximum tube capacity of 7 shells, VEPRs are typically used with factory 10-round magazines and have aftermarket options for 12-round stick mags or even 25-round drums.
Besides having a higher ammunition capacity, Veprs also have potentially faster reloads. While the M4’s tube magazine gives the option for quickly topping-off or for emergency-reloading a single round, it also takes longer to fully load. Even in the hands of an experienced user, it simply takes longer to stuff seven shells into an M4’s loading port than it does to shove a new mag into a Vepr and drop the bolt. Vepr magazines aren’t rock-and-lock like traditional AKs, they are inserted straight into a magwell like on an AR, which makes the process even quicker.
The M4’s telescopic stock is pretty iconic, but it is not as compact as the folding stocks found on Veprs. When paired with a folding stock and a short barrel, these AK shotguns are certainly in the running for guns with the most firepower in the smallest package.
Assuming that the M4 and Vepr-12 have equal reliability, to me it seems that the only real advantage of the Benelli is that it is marginally lighter weight. The Vepr-12 has an average larger magazine capacity and quicker reloads all in a smaller package that costs less than a Benelli. I may have a pro-AK bias, but I truly believe that AK shotguns are the best designed modern combat shotgun on the market. If you are in the market for a semi-auto 12-gauge, try looking a little further East than Italy and you may be pleasantly surprised at what you find.
The P320 AXG Pro takes Sig’s most popular full-size 9mm and gives it an all-metal frame and modern features to bring this service pistol to the next level.
What’s New On The P320 AXG Pro?
AXG Metal Frame
XSeries Flat Trigger
Sig Pro-Cut Slide
XRAY3 Day/Night Sights
Optics Ready
The Sig Sauer P320 was released in 2014 and adopted as America’s new M17 service pistol in late 2017. This full-size, double-stack, striker-fired 9mm handgun has become an increasingly popular choice for shooters since its release, and Sig has already produced a few different P320 variants. The new P320 AXG Pro’s features are designed to make the P320 platform as nice shooting as possible by mitigating recoil, improving ergonomics, and adding modularity.
SIG Talk: Explore Reviews, Tips, and Insights
SIG Sauer P320 – The Modular Handgun Redefining Performance
The AXG in the P320 AXG Pro’s name stands for “Alloy XSeries Grip”, and it is one of the biggest deviations from the standard P320 design. Like most modern striker-fired pistols, the P320 is polymer-framed. Polymer certainly has its advantages, namely weight and cost, but a metal frame like the one found on the P320 AXG Pro will absorb more recoil and make for a softer-shooting gun.
Metal is obviously more durable as well, and it is more likely to survive being dropped off a building or being used as a melee weapon. At least for me, a metal gun will always feel better in the hand than a polymer one.
The AXG frame comes with black Hogue G10 grip and backstrap panels, a deep undercut, and an extended beavertail to improve the gun’s ergonomics.
The AXG magwell is detachable, giving the option for either easier reloads or a slimmer profile. The P320 AXG Pro also comes with two 17-round mags with Henning Group Aluminum basepads.
The included XSeries flat-faced trigger cleanly breaks at 90 degrees and has an improved reset for quicker, more accurate shooting.
Pro-Cut Slide
Some of the weight added by the alloy frame is displaced by the lightning cuts that have been machined into the Sig Pro-Cut slide. The slide is full length to accommodate the 4.7-inch barrel and is cut to accept common pistol optics such as the Delta Point Pro, RMR, or Sig’s own ROMEO1Pro without the need for an adapter plate. The included iron sights are XRAY3 Day/Night sights which use a 3-dot Tritium system.
The new P320 AXG Pro from Sig looks like a great option for someone who is already familiar with the P320 family of pistols and is looking for a performance model that can excel in either a competition or defensive role. These pistols are now available from retailers, but the MSRP has not been posted. They have been seen listed online for $1,199.99, however, so it seems that these upgrades come at a premium.
For more information on Sig Sauer, please visit sigsauer.com.
Designed specifically for civilian defensive shooters, Federal Punch cuts costs of defensive ammo, but not at the expense of performance.
How Does Punch Differ From Other Defensive Ammunition:
Ammunition is not designed to meet FBI barrier standards.
Given the testing and engineering to meet these standards are cut out, the ammunition cost considerably less.
It's engineered to perform exceptionally well through heavy clothing.
Through this barrier, the ammunition provided adequate expansion and penetration.
Most of the really good defensive handgun loads on the market have one thing in common—they were designed to perform well in the Federal Bureau of Investigation’s testing protocol. This test assesses a bullet’s ability to inflict an effective wound after defeating various intervening obstacles commonly present in law enforcement shootings, like steel, plywood, wallboard and automotive safety glass. The best performing bullets in this test tend to expand to 1.5 times their original diameter and penetrate to between 12 and 18 inches, regardless of the intermediate barrier.
Paired with a compact 1911 like the Remington R1 Ultralight Executive, the new .45 Auto self-defense load can pack—pardon the pun—quite a punch.
This testing protocol has driven the manufacture of defensive handgun ammunition for the last 30 years, and manufacturers have become really good at building bullets to meet the FBI standard. And, as law enforcement agencies adopt loads based on their performance in this test, so too do civilians; the general population likes to be equipped as well as the cops. However, building bullets to meet this standard is expensive. Not only is the conduct of the extensive testing expensive, but so, too, is the engineering and building of the bullets that’ll perform well in them.
It’s possible that a civilian might need to shoot through steel, plywood, wallboard and automotive safety glass in order to save their life—but it’s not likely. The engineers at Federal have a tremendous amount of experience when it comes to building good defensive handgun ammunition, and they realized that civilians don’t necessarily need FBI duty ammunition. They felt they could create loads for defensive handguns that would perform exceptionally well when fired through heavy clothing, which is the most common intermediate barrier civilians encounter. And they felt that they could do this and offer the ammunition at a substantial savings to the consumer.
Punch Protection The result is a new line of self-defense ammunition called “Punch.” A 20-round box of 9mm Punch ammo has a suggested retail price of $15.99. A 20-round box of 9mm Federal Hydra-Shock ammo has a suggested retail price of $24.99. That equates to a 36 percent savings.
Rather than developing a single bullet design for all of the different Punch loads, the team at Federal evaluated each cartridge individually to determine which bullet design and weight would work most effectively. Since the bullets weren’t specifically designed to perform in FBI protocol testing, Federal spent time tuning each Punch load to meet the primary needs of the self-defense shooter—namely expansion and penetration.
Chris Laack, Federal’s handgun ammunition product manager, said, “We looked at specifications from our Hydra-Shok Deep, HST and other bullet designs, and we took what made sense for Punch. We selected whatever elements worked best for each individual caliber. We then played with thickness of the jacket, skive depth, hollow-point geometry and differences in lead cores to build the Punch recipe.”
Instead of building a single bullet design for each cartridge, one that would perform well on all types of intermediate barriers, Federal crafted bullets that would work exceptionally well on the barrier most civilian shooters might encounter during a self-defense shooting.
But, Does Punch Work? This all sounds fascinating, but the question is: Does it work? Based on my testing, it would appear so. I conducted some expansion and penetration tests with the 380 Auto, 9mm Luger and .45 Auto Punch loads. No, I didn’t conduct FBI protocol tests. This is partly because I don’t work for the FBI, and partly because the FBI and their comprehensive testing isn’t the final word on the terminal performance of defensive handgun ammunition. The results from my test were very promising—promising enough to convince me this ammunition has been well designed for the purpose it’s intended for, and that’s to provide civilians with a less expensive and very capable self-defense handgun load.
On average, the 9mm Luger and .45 Auto loads expanded to about 1.5 times their original diameter and penetrated between 14 and 15 inches. This level of performance is comparable to what you’d expect from other more expensive loads that perform well on all aspects of the FBI testing protocol, when they’re fired through heavy clothing.
The .380 Punch load deformed with a frontal diameter 1.4 times its original diameter and penetrated to 10 inches. As far as the .380 Auto goes, this is very good performance. If you want more penetration from a .380 Auto, Federal has another load you should consider. It’s called Hydra-Shok Deep, and it’ll stretch .380 Auto penetration past that magic FBI 12-inch mark. But it also costs about $7 (43 percent) more per box. If you’re willing to pay 36 cents more per shot, it’s clearly the better option.
At this time, the new Punch line from Federal has offerings for the .380 Auto, .38 Special, 9mm Luger and .45 Auto. And, if anyone cares anymore, Federal even has a load for the .40 S&W. Retail prices range between $15.99 for the .380 Auto and .38 Special, and $19.99 and $21.99 for the 9mm, .45 Auto and .40 S&W.
The new M-LOK Competition Bipod from Sport Ridge is tough, functional, and low-profile.
M-LOK Competition Bipod Specs:
Low-Profile M-LOK Mount
360° Pan, 15° Tilt
45° Or 90° Leg Deployment Capability
Adjustable Leg-Height From 7 To 9 Inches, ½-Inch Increments
MSRP Of $119.99
Bipods may seem simple enough, but anyone who has experience using them will tell you many designs are finicky and uncooperative. They are a tricky thing to get right, and all it takes is a cursory look at the machine guns of WWI to tell you that. Technology has certainly improved since then, but many bipods on the market today are almost as bad as those used in the Great War. Care must be taken when selecting one of these devices.
Sport Ridge’s new M-LOK Competition Bipod appears to have been well-designed with functionality and durability in mind for hard, real-world use.
Tough
Because a bipod’s legs act as concentrating points for the weight of the rifle, it is imperative that they are strong enough to not bend under the additional weight of the shooter leaning on it.
Constructed from aircraft-grade aluminum and then anodized matte black, the new M-LOK Competition Bipod should be able to withstand typical abuse imparted on it during competition use or in the field.
Functional
The M-LOK Competition Bipod was designed to be versatile, and that means a high level of adjustability. The legs, which are attached via a low-profile M-LOK mount, can pan a full 360 degrees around and 15 degrees of up-and-down tilt. This should provide for a wide range of motion and give the shooter a maximum possible area of coverage.
The legs can also be deployed at either a 45-degree or 90-degree pitch, and have independently adjustable lengths with 3-inches of variation. These features should ensure a stable shooting position regardless of how uneven the ground is.
The new Sports Ridge bipod also has a tension adjustment lever that can be fine-tuned to your preferred tension level.
Available today with an MSRP of $119.99, this rugged bipod is ready for your next competition.
For more information on Sport Ridge, please visit sportridge.com.
Looking to go armed, but are stuck in the weeds as to what to arm yourself with? Here are 20 excellent concealed carry gun options that will keep you on the defensive.
