M1 Garand Bayonet for the Ultimate Survival Gun

M1 Garand Bayonet for the Ultimate Survival Gun
Don't expect to use a bayonet in an old-fashioned charge nowadays.
M1 Garand bayonet, not a bad idea for a survival gun.
M1 Garand bayonet, not a bad idea for a survival gun.

Why would someone attach an M1 Garand bayonet to their rifle today? One good reason is covered in this article about survival guns.

History of the M1 Garand Bayonet

For civilian use, little thought has been given to the M1 Garand bayonet, other than interest as collectors’ curiosity. With preparation for civil disaster, the bayonet should no longer be considered a collector piece, but as an essential item in the survival toolbox.

Starting in late WWII, the bayonet changed in form and function. Prior to that time, most military bayonets were almost a type of short sword, with a blade roughly from 10-17 inches in length.

This length gave the soldier maximum reach for thrusting through their opponent when battle was close or ammo was low.

However, this bayonet length, or the spike-style bayonet on the SKS was really not good for a whole lot of other purposes, and it spent most of its time adding weight to a soldier’s belt without maximum utility.

As WWII progressed, and the M1 carbine was in front-line combat service, there arose a cry for a bayonet that would fit it. Due to the short length of the carbine, the old school full-length sword bayonets would unbalance the gun severely.

The M4 bayonet was introduced along with the barrel band bayonet lug. The M4 was much like the Ka-Bar fighting knife that was made for the U.S. Marines.

With a 6.5-inch blade length which could be sharpened on both sides, the bayonet was no longer a little-used burden for a soldier to carry, but a piece of equipment that could be used as a bayonet, fighting knife or tool for prying or opening rations.

Eventually the M5 knife/bayonet was introduced for the M1 Garand, which replaced the “sword blade” bayonets that were previously issued. The M5 used the same blade as the M4 and was equipped with a plastic handle.

The Switch to Knife Bayonets

The advantages of the knife bayonet were not lost on the rest of the armies in the world and many followed suit by switching to knife-style bayonets.

M1 Garand Bayonet as a retention tool
An M1 Garand bayonet works well against someone trying to grab your survival gun.

Use of the bayonet on today’s survival rifles is not for last-ditch bayonet charges. Where the bayonet shines is for use as the ultimate weapon retention device.

There are a many long gun retention techniques taught to law enforcement officers in order for them to safeguard and control their guns (although my method of defense is a pull of the trigger to discourage the attempt) but affixing a bayonet is most likely the best method of retaining control. Even though some long-range accuracy may be degraded, any close-quarter gun grab would be stopped immediately.

In addition, the modern bayonet is of course, a knife and a tough one at that.

If you have a rifle that can accept a bayonet, find a good used one or a new reproduction model, and make it your survival knife to maximize its usefulness. Anything you are carrying for emergency evacuation use should have as many uses as possible for it to earn a space on your body.

Today's Bayonet Legacy

Looking forward from the M1 Garand Bayonet is the newest M-16 bayonet, the M9. There are a number of manufacturers who make the M9, which has more focus as fixed-blade survival knife, since that is the most likely use for this tool in today’s army.

The M9 is an upgraded version of the previous M-16 bayonet, the M7 in that a wire cutter attachment has been added to the scabbard tip in a fashion similar to the design on the AK-47 knife/bayonet, and the handle is hollow for storage of a small amount of survival items.

The M9 makes a very fine stand-alone survival and camping knife even without the rifle to go with it.

Note that the M9 can be added to properly equipped Mossberg 500/590 shotguns as well, which helps address their lower magazine capacity issue. 

Any rifle that can mount a bayonet should have one available for it. If you have one of the Auto-Ordnance M1 carbines, a barrel band bayonet lug can be added to it with little effort.

All in all, the M1 Garand bayonet should be considered a serious option for today's survival guns.

M1 Garand Bayonet Update

U.S. military bayonets of World War II. Shown are the M1905 Bayonet (blued version), M1 Bayonet, M1905E1 Bowie Point Bayonet (cut down version of the M1905), and the M4 Bayonet with leather handle for the M1 Carbine. Photo: Curiosandrelics
U.S. military bayonets of World War II. Shown are the M1905 Bayonet (blued version), M1 Bayonet, M1905E1 Bowie Point Bayonet (cut down version of the M1905), and the M4 Bayonet with leather handle for the M1 Carbine. Photo: Curiosandrelics

M1 Garand Bayonet Identification

The M1 Garand bayonet’s history is as varied as the gun itself and identifying a Garand bayonet would require an entire dissertation unto itself.

The main bayonets used on the big M1 were the M1905, M1, M5 and M5A1. M1905 Bayonets Type I-III sport walnut grips, while the Type IVs have plastic grips. M1s and M5s also carry plastic slabs.

Early M1905 bayonets had blued 16-inch blades, later models were Parkerized. Manufacturers included Wilde Drop Forge & Tool (WT)Utica Cutlery (UC)Union Fork & Hoe (UFH)Pal Blade & Tool (PAL)Oneida (OL)American Fork & Hoe (AFH).

The M1 was similar in appearance to the M1905, only with a shorter 10-inch blade. The M5 variants were 6-inchers.

M1 Garand Bayonet Reproduction

While there are lots of samples of original M1 Garand Bayonets on the used market, there are some companies making reproductions.

For example, Atlanta Cutlery sells a reproduction M1 bayonet, complete with 1942 markings and the flaming bomb cartouche.

Dig Deeper into the M1 Garand:

Be sure to check out the Standard Catalog Of Military Firearms, 9th Edition.

Corey Graff contributed to this article.


Next Step: Get your FREE Printable Target Pack

Enhance your shooting precision with our 62 MOA Targets, perfect for rifles and handguns. Crafted in collaboration with Storm Tactical for accuracy and versatility.

Subscribe to the Gun Digest email newsletter and get your downloadable target pack sent straight to your inbox. Stay updated with the latest firearms info in the industry.


  1. And one more thing!!! If one googles “bayonet lug clamp” they will see all kinds of nifty devices to allow for a bayonet to be attached to a rifle that does not have a lug. I have fired a Saiga in 7.62 X 39 with an M7 bayonet on it. The lug could only be clamped to the barrel so far back before hitting the handguard, so a piece of 3/4″ hard copper pipe was epoxied to the barrel hole in the bayonet with holes drilled through it to vent muzzle blast, and lined with a 12 gauge plastic hull, sans base, to fit it to the Saiga barrel more snugly. FIX BAYONETS!!!

  2. I did not see it mentioned that a fighting knife, bayo or elsewise, needs to be slightly heavier on the handle end, so that if the hand is opened, the knife remains in hand instead of falling to the ground. I have several bayonets and all have this trait. Recently I bought a knife that is a very nice version of a fighting knife, very similar to an M3, but it is light in the handle and will literally fall out of your hand if you open it. If you are used to a knife that stays in your hand when you open your grip, it is quite disconcerting to do so with a knife that does not, particularly if you are messing with it in your room in stocking feet, watching it fall point first between them!!! If you have never experienced that, right now you are saying “so what, this guy talks too much”!!!

  3. The handle of the M9 may be hollow, as therein rides the rod that connects the latch to the blade but it’s certainly not hollow for storage.

    @biteme, the barrel band on the 590 that holds the front sling swivel had a bayonet lug on it.

    • Tweak is right. I missed that in researching the evolution of the original Buckmaster 184 into the M9 bayonet. Thanks for catching that!

  4. The original pupose of bayonets was to eliminate the need for pikemen to protect musketmen from cavalry. This endured up until the early 20th century. When the British adopted the SMLE to replace the “Long Lee” rifle, they also introduced a shorter bayonet. Fairly soon after, a longer bayonet was adopted because the infantry complained that the shorter blade, along with the shorter rifle, did not give them enough “reach” to counter a mounted cavalryman.

  5. You wrote ‘Note that the M9 can be added to properly equipped Mossberg 500/590 shotguns as well, which helps address their lower magazine capacity issue. ‘

    Please advise other than welding it to the barrel where can you get adapters the fit it to the Mossberg 590?

    • Many of the military versions of the Mossberg were equipped to accept the M9 bayonet on the forward end of the magazine tube. I don’t know if there are aftermarket mounts or not, but the shotguns are out there if you look for them.

      • I bought a Mossberg 590 SPX that actually came from Mossberg new with an Ontario M9 bayonet in the box as well. It mounts right onto the lug/near the end of the magazine tube.


Please enter your comment!
Please enter your name here

This site uses Akismet to reduce spam. Learn how your comment data is processed.