Gun Digest

AR Basics: Mastering The Nuances of Charging Handle And Bolt Release

Charging Handle 2
On an empty reload, the bolt catch serves as a bolt release. This is the way the AR is designed to function, and the more you mess with the charging handle, especially under stress, the more chance there is you’ll mess it up.

Of all the AR’s parts, the operation of the charging handle and bolt catch (also known as the bolt release) seems to confuse shooters most.

The charging handle assembly is used to manually cycle the bolt group during loading and unloading, and while clearing malfunctions and stoppages. To perform this and other tasks efficiently — and to prevent wear and tear on your AR — it’s important to implement the proper techniques when using the handle catch/release in tandem, as well as when using them independently.

Cycling the charging handle is a three-step process. Although it seems very straightforward, proper technique is the difference between efficient cycling and potentially damaging the charging handle — which will put your gun out of commission.

For starters, the charging handle is used when performing a chamber check. The handle and bolt catch are used together to manually lock the bolt open. However, you don’t use the handle to perform an empty reload; for that, you use the bolt catch as a release. Knowing when and how to use the charging handle and bolt catch in harmony is key to operating the AR efficiently.

Nuances of the Charging Handle

Improper technique of the charging handle creates friction and wear, and it requires more force than necessary. In fact, you can actually torque the handle out of shape. Once the handle is bent, the bolt carrier can’t reciprocate — and the AR ceases to function. Incorrect technique could also break the latch, allowing the charging handle to follow the bolt back, thereby impacting your head. Cycling the handle is all about using proper technique, not brute force.

Left-handed shooters use their trigger finger to release the bolt. By design, the AR is ergonomic for both right- and left-handed shooters. The key is learning how to manipulate it properly and then consistently using the proper technique.

Normally, the strong hand maintains its grip on the AR, and the support hand is used to operate the charging handle, which is a three-step process: First, position the thumb of the support hand on the back of the handle in its center. Next, use the index finger to unlatch. Then, using the elbow (not the shoulder), cycle the handle aggressively, pulling it straight to the rear. The thumb should follow the center line of the stock as it moves rearward, maintaining alignment between the handle and its channel in the upper receiver.

Need More AR Knowledge:

Once the handle has reached full extension, allow it to strip from your hand: Release it as you would a bowstring, allowing the bolt group to snap forward under full spring pressure.
The most common issue I see with the AR is students letting their support hand impede the handle and bolt group’s forward movement. This creates a stoppage, requiring additional manipulations. Pull the charging handle all the way to the rear and release it — every time.

To confirm the condition of the chamber, you perform a chamber check. The support hand holds the AR, and the strong hand comes off the grip to pull the handle back. For most other operations, the support hand runs the charging handle.

I teach left-handed shooters to use the first two fingers of the support hand (think “snake fangs”) on the left and right side of the handle, with the thumb centered in the back. Lefties can install an ambidextrous charging handle with a release on each side. Just remember that you might not always be firing your AR, so you must know how to work with a military-type handle.

Other Charging Handle and Bolt Catch Duties

As mentioned earlier, the charging handle is used to check the condition of the chamber. It sounds simple, right? Maybe, but “simple” and “smooth” are not the same thing.

With a magnified optic, you might need a wider charging handle, which allows you to use the proper techniques during manipulations. Just remember to get a high-quality handle; if it breaks or bends, your AR is out of operation.

After cycling the handle with the support hand, it’s repositioned on the handguard. The strong hand comes off the grip to the charging handle. Right-handed shooters use their “snake fangs” to grasp the handle; left-handers use the right-hand technique described above. The strong hand pulls the handle slightly to the rear, allowing you to confirm there’s a round chambered or that the chamber is clear.

The charging handle is also used to manually lock the bolt to the rear. Here, again, the strong hand is used to pull back on the charging handle, while the support hand is positioned at the magwell of the lower receiver. Right-handers use their left thumb to engage the catch; lefties use the index finger of the right hand.

Regardless of what handle type you choose, proper lubrication is mandatory. A combination of grease and oil offsets the other’s deficiency.

In addition, the charging handle is used to manually cycle the bolt group. To perform an empty reload when the bolt is locked to the rear, it’s best to use the bolt catch as a bolt release. Hitting the “bolt release” is the most efficient and ergonomic way to chamber a round during an empty reload.

A right-handed shooter releases the bolt by pressing with the thumb of the left hand. The new mag is inserted and locked in with the left hand, so the thumb is already there and ready to release the bolt. Left-handed shooters should use the right hand to feed a fresh mag and their trigger finger to release the bolt. Using the bolt catch as a release chambers a fresh round, and the bolt has the energy necessary to lock in battery. You’re now ready to fire.

Final Thoughts

The charging handle and bolt catch are critical components of the AR. They’re simple to use — as long as you use the correct technique.

Knowing when to use the charging handle and bolt catch separately or in unison is mandatory to operating the AR efficiently. And, as it is with any piece of precision machinery, it’s up to you to learn it well.

The article originally appeared in the May 2019 issue of Gun Digest the Magazine.

NEXT STEP: Download Your Free Storm Tactical Printable Target Pack

62 Printable MOA Targets with DOT Drills - Rifle Range in YARDS This impressive target pack from our friends at Storm Tactical contains 62 printable targets for rifle and handgun range use. Target grids and bullseye sizes are in MOA. Ideal for long-range shooting! Get Free Targets

Exit mobile version